Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
How do you feel when it comes to How to Install a Bathtub Yourself?
Setting up a tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is also a moderately challenging task. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open a wall surface to remove the old bathtub and place the brand-new bathtub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub and embeded in the brand-new one. See to it you have certified on your own for the job as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about employing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly help you set up a brand-new bathtub in your shower room if you have actually currently gotten a brand-new tub as well as don't require to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Preparing for the Installation
To start with, the sustaining frame provided with the bathroom must be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. When the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by examining the level and changing the feet on the bath tub till the level reviews degree.
To set up taps, fit the bottom of the outermost versatile faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system and also check all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bath tub and also check the overflow outlet as well as the normal outlet for leaks.
Lastly, take care of the bath paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub should wait till the bath tub has actually been made use of at the very least once as this will resolve it into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type needs to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bath as well as the tiling, leading to difficulties with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealer can split relatively early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the marketplace. It is suggested to fit the ceramic tiles utilizing waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub? Leave a remark directly below. We will be glad to know your suggestions about this piece. We are looking forward to see you back again in the near future. Sharing is nice. Who knows, you may be doing someone a favor. We truly appreciate reading our article about How to Install a Bathtub.
Address plumbing needs. Report this page